ASTM, ASME, ISO & EN certified — high-performance materials for critical industrial
applications.
Asia Bolts Industries manufactures fasteners from internationally approved raw materials at our
Dubai Investments Park facility. Every grade we supply is traceable by heat number from raw bar to finished
fastener, and every order ships with a Material Test Report (EN 10204 Type 3.1; Type 3.2 on request) confirming
chemical composition and mechanical properties to the applicable ASTM, ASME, ISO, EN and DIN requirements. From
alloy steel studs for oil & gas flanges to nickel alloy and titanium fasteners for extreme-temperature and
corrosive service, we manufacture to your specification.
High-strength alloy steel studs, bolts and socket head screws for high-pressure,
high-temperature and low-temperature service. Hardness, tensile and Charpy impact testing available.
Grades supplied
ASTM A193 B7
ASTM A193 B7M
ASTM A193 B16
ASTM A320 L7
ASTM A320 L7M
ASTM A320 L43
ASTM A354 BC
ASTM A354 BD
ISO 898-1 Class 12.9
ISO 898-1 Class 10.9 (alloy)
ASTM A574 socket head
42CrMo4 (1.7225)
AISI 4140 / 4340
EN 19 / EN 24 (legacy BS 970)
Dashed outline = recently added / extended range
Class 12.9: quenched-and-tempered alloy steel, minimum tensile 1220
MPa. Socket head cap screws to ISO 4762 / DIN 912 and ASTM A574. Supplied plain, black oxide, phosphate or
zinc-flake coated. Class 12.9 is not hot-dip galvanised, and electroplating requires
hydrogen-embrittlement relief.
Matching nuts & accessories
Nuts (ASTM A194)
Grade 2H (B7, A354 BD) · 2HM (B7M, sour service) · Grade 4 or 7 (L7) · 7M (L7M)
· Grade 7 or 4, or 16 where specified (B16)
Nuts for A354 BC
ASTM A563 Grade C
Nuts for Class 12.9
ISO 898-2 Property Class 12 (ISO 4032 / 4033 pattern)
Washers
ASTM F436 hardened · F844 plain
Sour service
NACE MR0175 / ISO 15156 compliant grades available on request
Stainless Steel Fasteners
Marine · Chemical · Food-grade
Austenitic, martensitic and precipitation-hardened stainless fasteners for corrosive, marine,
chemical and food-grade environments. Passivated or electropolished finish available.
Heavy-duty structural bolts, nuts and washers for steel construction, bridges, cranes and
infrastructure across the GCC, supplied as complete assemblies.
Grades supplied
ASTM F3125 Grade A325 (Type 1 / 3)
ASTM F3125 Grade A490 (Type 1 / 3)
ASTM F1852 / F2280 twist-off tension control
ISO 898-1 Class 8.8 / 10.9
ISO 4014 / 4017 (formerly DIN 931 / 933)
EN 14399 HR / HV preload assemblies
EN 15048 non-preloaded
ASTM A563 nuts
ASTM F436 washers
A325 and ISO 8.8 are comparable in strength, as are A490 and ISO 10.9, but the standards
are not interchangeable. State the governing specification on your enquiry. See our ASTM A325M heavy hex bolts page for details.
Matching nuts & finishes
Nuts
A563 Grade DH (A325 & A490) · DH3 (weathering) · ISO 4032 Property Class 8 / 10
Hot-dip galvanising
ISO 1461 / ASTM F2329 / ISO 10684, available for A325 and ISO 8.8 assemblies
A490 & Class 10.9+
Supplied plain or with a coating suitable for high-strength steel (hydrogen embrittlement risk)
Assemblies
Bolt, nut and washer sets per ASTM F3125 and EN 14399
Duplex & Super Duplex Fasteners
Offshore · Seawater · Chloride
service
High strength combined with strong resistance to pitting, crevice corrosion and chloride
stress corrosion cracking. Widely specified for offshore platforms and seawater systems, and for sour service
where permitted by ISO 15156-3.
Grades supplied
UNS S31803 / S32205 (2205 duplex)
UNS S32750 (2507 super duplex)
UNS S32760 (Zeron® 100)
UNS S32101 (lean duplex)
UNS S32304 (2304 lean duplex)
Nuts & documentation
Matching nuts
Supplied in the same duplex alloy as the stud or bolt
Documentation on request
NACE MR0175 / ISO 15156 compliance · PREN calculations · impact test reports ·
ferrite content
High Nickel & Special Alloy Fasteners
Extreme temperature · Aggressive
media
Precision-machined fasteners for extreme-temperature, high-pressure and highly corrosive
service in petrochemical, offshore and power generation applications. Material certification to ASTM B164, B865,
B637, B446, B574 and B473, and to AMS where required. See also our exotic
material fasteners page.
Grades supplied
Alloy 625 (N06625)
Alloy 718 (N07718)
Alloy 600 (N06600)
Alloy 825 (N08825)
Incoloy 800H / 800HT (N08810 / N08811)
Nickel 200 (N02200)
Monel® 400 (N04400)
Monel® K-500 (N05500)
Hastelloy® C-276 (N10276)
Hastelloy® C-22 (N06022)
Alloy 20 (N08020)
A-286 (S66286, ASTM A453 Gr. 660)
Nuts & certification
Matching nuts
Same alloy as the bolt per the relevant bar specification: B164 (Monel 400, Nickel 200 per B160), B574
(Hastelloy), B446 (Alloy 625), A453 Gr. 660 (A-286)
Titanium
See the Titanium section below
Certification
AMS and NACE MR0175 certifications available on request
Carbon Steel Fasteners
Highest-volume family · Fast dispatch across the
GCC
Standard and high-strength carbon steel fasteners for general construction, infrastructure
and mechanical applications. Full material test certificates with every order.
Grades supplied
ASTM A307 Grade A / B
ASTM F1554 Grade 36 / 55 / 105 anchor bolts
SAE J429 Grade 2
SAE J429 Grade 5 (inch)
SAE J429 Grade 8 (inch)
ASTM A449
ISO 898-1 Class 4.6
ISO 898-1 Class 5.6 / 5.8
ISO 898-1 Class 6.8
ISO 898-1 Class 8.8
ISO 898-1 Class 9.8
ISO 898-1 Class 10.9
Threaded rod & stud bar (DIN 975 / 976-1 legacy)
Class 12.9 alloy fasteners are listed under Alloy Steel.
Nuts, finishes & washers
Nuts
A563 Grade A (A307) · Grade C (SAE Gr.5 / A449) · Grade DH (SAE Gr.8) · ISO 4032 /
ISO 898-2 Class 6 / 8 / 10 (formerly DIN 934)
Finishes
In-house hot-dip galvanising (ISO 1461 / ASTM F2329) and electro-zinc plating (ASTM B633). These are
separate processes with different coating thicknesses.
Washers
F844 plain · F436 hardened · ISO 7089 / 7090 / 7093 (formerly DIN 125 / 9021)
Titanium Fasteners
Seawater · Desalination · Aerospace
Excellent strength-to-weight ratio and outstanding corrosion resistance in seawater,
chlorinated media and oxidising environments, at roughly half the weight of steel. Full traceability to ASTM
B348 (bar); Grade 5 also to AMS 4928.
Grades supplied
Grade 2 (R50400) commercially pure
Grade 5 / Ti-6Al-4V (R56400)
Grade 7 (R52400) Pd-stabilised
Titanium is prone to galling. Use anti-seize compound and controlled tightening.
Minimum values for sizes up to M16 where the standard distinguishes by diameter. Refer to ISO
898-1 for the full table.
Class
Material
Min. tensile (MPa)
Min. yield / proof (MPa)
Matching nut class (ISO 898-2)
4.6
Low / medium carbon steel
400
240
4 or 5
5.8
Low / medium carbon steel
500
420
5
6.8
Medium carbon steel
600
480
6
8.8
Medium carbon, quenched & tempered
800
640
8
9.8
Medium carbon, quenched & tempered
900
720
9
10.9
Carbon-boron or alloy, quenched & tempered
1040
940
10
12.9
Alloy steel, quenched & tempered
1220
1100
12
Grade Selection Guide
Starting point only
Final selection depends on temperature, pressure, media and the governing project
specification. Our technical team will confirm it with you.
Service condition
Typical grades
High-pressure / high-temperature flanges
ASTM A193 B7 or B16 with A194 2H
Low-temperature service
ASTM A320 L7 / L43 with A194 Grade 4 or 7
Sour (H2S) service
A193 B7M / A320 L7M with A194 2HM, to NACE MR0175 / ISO 15156
Marine, chemical, food-grade
Type 316 / 316L, A193 B8M, 904L
Seawater and offshore
Duplex / super duplex, Alloy 625, titanium Grade 2
Aggressive acids and chlorides
Hastelloy C-276 / C-22, Alloy 20, Alloy 825
Very high temperature
Alloy 718, A-286, Incoloy 800H / HT
Steel structures and bridges
ASTM F3125 A325 / A490, ISO 8.8 / 10.9 assemblies
Compact, high-strength joints, socket head
ISO 898-1 Class 12.9 (ISO 4762 / A574)
General construction and anchoring
A307, F1554, SAE Gr.5, ISO 4.6 to 8.8 (galvanised)
Need a grade that isn't listed?
We manufacture to your drawing and specification. Send us your requirements, standard, grade and quantity,
and our team will respond with a quotation and the applicable certification.